Can I put that on my ICS M4A1 R.I.S?

Damascus · September 24th, 2005, 01:14

Hi all,
I have an ICS M4A1 R.I.S and i'm trying to find another method than the Battery Box for my battery storage.
I've seen this on Redwolf Airsoft :
G&P M4A1 Extended Battery Buttstock (Black) for Marui M4 Series
at this page : http://www.redwolfairsoft.com/redwolf/airsoft/Category?
I know they are saying that's for Marui but can you say me if it would be compatible with ICS ones?
Oh, and another question, how to change the FlashHider? I think i need a sort of
Hexagonal Key...

so...
Thanks ^^

Brakoo · September 24th, 2005, 01:20

You could install this but keep in mind that the wiring will have to be rerouted to the back of the gun and you'll have to buy a battery made specificly for this. As for the flashhider, yes you need an hex key to remove it. I recommand you get yourself a complete set of hex screw, they're pretty much necessary if you start thinkering with your gun. I bought a complete set at Wal-Mart for 9.99$ so they're not too expensive.

Damascus · September 24th, 2005, 01:27

Ok thanks, for the Hex Key kits, I have all of them...
For rerouting the wiring I will have to open all the gun?
I think that worth the job for putting away this ugly battery box lol...

thanks again

nutboi · September 24th, 2005, 02:43

u can purchase a peq and put a battery in there. you can mount it on your ris.

Damascus · September 24th, 2005, 11:33

PEQ is the same thing with laser...
It's also ugly...

mcguyver · September 25th, 2005, 12:59

you can buy either the ics s.i.r rail kit or the samurai s.i.r from wgc and replace your rail. these both hold batteries but they are like $179 u.s. plus freight, etc. unless you are a mechanical whiz don't bother rewiring your mechbox for the g&p stock. the stock won't fit (you must modify the rectangular keys on the lower mechbox with a dremel) and completely strip down your lower mechbox to reroute the wiring. you could buy a stock lower box premade from ics for fixed stck but it has to come from asia as airsoft elite (the exclusive north american distributor) doesn't currently have them. i know because i have the ics m4 r.i.s. and was checking out alternatives but opted to stay stock.you can fit a 9.6 1700mah battery in that faux peq and it should be available from your ics retailer. it will also fit 2 8.4 minis and you cal parallel wire them for game use and then disconnect after. unfortunatley with their rail system the box is your only choice without extensive mods to this gun. if you want to balance the gun out a but so all the weight is not centered forward of the mag, buy the g&g sopmod stock. it fits with little effort.

Damascus · September 25th, 2005, 14:01

thanks... I think for the moment, because i don't use my rails now, i will only buy a normal m4 hanguard at 70$ on rangers airsoft. Will it fit?

mcguyver · September 25th, 2005, 14:24

make sure it's an ics handguard. others may not fit and positively lock within the delta ring set-up. ics parts are generally proprietary and not interchangable with other brands. tm,g&P and some(not all)g&g parts are interchangeable. with an ics m4a1 you can fit a 9.6 1700mah nunchuck battery in the foregrip so with the proper grip you should be able to as well.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

September 24th, 2005, 01:14	#1
Damascus formerly sstrunks Trader rating Join Date: May 2005 Location: St-Sauveur, QC	Can I put that on my ICS M4A1 R.I.S? Hi all, I have an ICS M4A1 R.I.S and i'm trying to find another method than the Battery Box for my battery storage. I've seen this on Redwolf Airsoft : G&P M4A1 Extended Battery Buttstock (Black) for Marui M4 Series at this page : http://www.redwolfairsoft.com/redwolf/airsoft/Category? I know they are saying that's for Marui but can you say me if it would be compatible with ICS ones? Oh, and another question, how to change the FlashHider? I think i need a sort of Hexagonal Key... so... Thanks ^^

September 24th, 2005, 01:20	#2
Brakoo Trader rating Join Date: Dec 2003 Location: Laval, Quebec	You could install this but keep in mind that the wiring will have to be rerouted to the back of the gun and you'll have to buy a battery made specificly for this. As for the flashhider, yes you need an hex key to remove it. I recommand you get yourself a complete set of hex screw, they're pretty much necessary if you start thinkering with your gun. I bought a complete set at Wal-Mart for 9.99$ so they're not too expensive. __________________

September 24th, 2005, 01:27	#3
Damascus formerly sstrunks Trader rating Join Date: May 2005 Location: St-Sauveur, QC	Ok thanks, for the Hex Key kits, I have all of them... For rerouting the wiring I will have to open all the gun? I think that worth the job for putting away this ugly battery box lol... thanks again

September 24th, 2005, 02:43	#4
nutboi Trader rating Join Date: Apr 2005 Location: richmond bc	u can purchase a peq and put a battery in there. you can mount it on your ris.

September 24th, 2005, 11:33	#5
Damascus formerly sstrunks Trader rating Join Date: May 2005 Location: St-Sauveur, QC	PEQ is the same thing with laser... It's also ugly...

September 25th, 2005, 12:59	#6
mcguyver Trader rating Join Date: Aug 2005 Location: Northern Alberta	you can buy either the ics s.i.r rail kit or the samurai s.i.r from wgc and replace your rail. these both hold batteries but they are like $179 u.s. plus freight, etc. unless you are a mechanical whiz don't bother rewiring your mechbox for the g&p stock. the stock won't fit (you must modify the rectangular keys on the lower mechbox with a dremel) and completely strip down your lower mechbox to reroute the wiring. you could buy a stock lower box premade from ics for fixed stck but it has to come from asia as airsoft elite (the exclusive north american distributor) doesn't currently have them. i know because i have the ics m4 r.i.s. and was checking out alternatives but opted to stay stock.you can fit a 9.6 1700mah battery in that faux peq and it should be available from your ics retailer. it will also fit 2 8.4 minis and you cal parallel wire them for game use and then disconnect after. unfortunatley with their rail system the box is your only choice without extensive mods to this gun. if you want to balance the gun out a but so all the weight is not centered forward of the mag, buy the g&g sopmod stock. it fits with little effort.

September 25th, 2005, 14:01	#7
Damascus formerly sstrunks Trader rating Join Date: May 2005 Location: St-Sauveur, QC	thanks... I think for the moment, because i don't use my rails now, i will only buy a normal m4 hanguard at 70$ on rangers airsoft. Will it fit?

September 25th, 2005, 14:24	#8
mcguyver Trader rating Join Date: Aug 2005 Location: Northern Alberta	make sure it's an ics handguard. others may not fit and positively lock within the delta ring set-up. ics parts are generally proprietary and not interchangable with other brands. tm,g&P and some(not all)g&g parts are interchangeable. with an ics m4a1 you can fit a 9.6 1700mah nunchuck battery in the foregrip so with the proper grip you should be able to as well.

Can I put that on my ICS M4A1 R.I.S?

Airsoft Guns Discussion