Marui Sig p226 problems

vam907 · September 9th, 2007, 15:03

Hey, for some reason I can't post in the gun problem section so i might as well say it here...

I'm having problems with my Marui Sig p226. I've had it for about two years and run it on propane. Every time i fire it now, the bbs drop to the ground about a meter away, after leaving the barrel. Sometimes, even two bbs will fire out with one trigger pull and do this. I've tried adjusting the hop up and looking inside, but I don't know what's wrong and don't know much about repairing airsoft guns.

Anyone have an idea of whats wrong? or have the same problem?........Thanks.

dodger_me · September 9th, 2007, 15:22

turn hop up COMPLETELY off then clean the barrel and relube everything then take it from there

vam907 · September 9th, 2007, 15:40

sure ill try that sometime.........thanks a lot

dodger_me · September 9th, 2007, 15:55

also clean the blowback chamber if it doesnt fix it

ILLusion · September 9th, 2007, 18:40

When you fire, is there an excessive amount of gas blowing out of the slide? It sounds to me like your blowback chamber is possibly blown, regarding the firing characteristics.

vam907 · September 9th, 2007, 20:54

Today i tried just one bb in the mag and it worked fine........if i have more than one bb, the gun does what i said earlier

ILLusion · September 9th, 2007, 21:12

Check the loading nub on the nozzle isn't broken off.

CuppoJava · September 13th, 2007, 01:51

I had this problem with my KSC g34 and TM Hi-Capa 5.1,
For me, it was caused by excess oil on the hop-up rubber which causes bb's to slide past it when chambered too hard.

the thing that worked for me was:

taking the gun apart and cleaning everything, (be careful not to rip the hop-up rubber when removing it)

soak the hopup rubber in water with dish-water detergent,

lube everything EXCEPT the hopup,

put gun back together.

See if that works.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

September 9th, 2007, 15:03	#1
vam907 Trader rating Join Date: Oct 2005 Location: St. John's Newfoundland	Marui Sig p226 problems Hey, for some reason I can't post in the gun problem section so i might as well say it here... I'm having problems with my Marui Sig p226. I've had it for about two years and run it on propane. Every time i fire it now, the bbs drop to the ground about a meter away, after leaving the barrel. Sometimes, even two bbs will fire out with one trigger pull and do this. I've tried adjusting the hop up and looking inside, but I don't know what's wrong and don't know much about repairing airsoft guns. Anyone have an idea of whats wrong? or have the same problem?........Thanks.

September 9th, 2007, 18:40	#5
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	When you fire, is there an excessive amount of gas blowing out of the slide? It sounds to me like your blowback chamber is possibly blown, regarding the firing characteristics. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

September 9th, 2007, 21:12	#7
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	Check the loading nub on the nozzle isn't broken off. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

September 9th, 2007, 15:40	#3
vam907 Trader rating Join Date: Oct 2005 Location: St. John's Newfoundland	sure ill try that sometime.........thanks a lot

September 9th, 2007, 20:54	#6
vam907 Trader rating Join Date: Oct 2005 Location: St. John's Newfoundland	Today i tried just one bb in the mag and it worked fine........if i have more than one bb, the gun does what i said earlier

September 13th, 2007, 01:51	#8
CuppoJava Trader rating Join Date: May 2006 Location: Calgary	I had this problem with my KSC g34 and TM Hi-Capa 5.1, For me, it was caused by excess oil on the hop-up rubber which causes bb's to slide past it when chambered too hard. the thing that worked for me was: taking the gun apart and cleaning everything, (be careful not to rip the hop-up rubber when removing it) soak the hopup rubber in water with dish-water detergent, lube everything EXCEPT the hopup, put gun back together. See if that works.

Marui Sig p226 problems

Airsoft Guns Discussion