TM Glock 17 magazines - ReFill problem

Slide · January 30th, 2012, 11:40

Hi all,

i have bhought a TM Glock 17 recently and the gun is working very well but i experienced some trouble with the mags (TM too).

There is no leaking when they are filled, but when i fill the mags, it's impossible to make a clean "sealed" refill, gas is going out everywhere. It's like the gas adaptater doesn't fit with the inlet valve.
Wich is very classy when you are using propane gas

It seems the valve is too little...i have try every angle possible...plastic adaptater, metal adaptater, green gas bottle. Same thing with all of this.

So i was wondering if it's a known issue about the Glock 17 TM mags? Or only the two i have bhought...and if you have a solution or recommandation.

Thanks guys!

Photo of the mag and valve :

Armen000 · January 30th, 2012, 11:51

Theres usually a nice little rubber oring that sits in there, from your picture it doesn't look like you have one :P

Spike · January 30th, 2012, 11:57

Most TM mags are like that, very messy fill. Can be solved with an O ring, like Armen said.

anthon · January 30th, 2012, 11:58

Yes, TM mags are suposted to make the loud hissing noise when you fill them. AS long as its not leaking after your done filling the mags are normal.

I would not recommend using those little rubber o rings, i used one in one of my mags and never again! sure it made them quite when they are filled, but the problem was that it made the mag a hell of a lot harder to fill up.

Amos · January 30th, 2012, 12:03

TM fill valves are do that.

Slide · January 30th, 2012, 12:05

Ok so i have open up the bottom mag and the O ring on the valvle is very used....so as you say replacing it by a new one will help... Any idea where i can buy this? Thanks!

ShelledPants · January 30th, 2012, 12:12

As said above, TM do not fill like KSC, they spray a little when you fill them. This is by design.

ILLusion · January 30th, 2012, 12:51

If it doesn't leak when filled, then that o-ring is fine, even if it appears worn to you. Don't worry about it.

As already mentioned, TM fill valves WILL emit gas while filling - again, this is by design and on purpose.

Slide · January 30th, 2012, 13:29

Perfect! Thanks guys!

MultipleParadox · January 30th, 2012, 16:33

Same thing surprised my when I filled my HiCapa's mags
It was very messy, to the point where it was slightly dripping liquid propane (god damns this thing is cold on your hands!)

Once filled it hold it tight; The dripping is actually a feature for you not to get too hot in the summer :P

AKA · January 30th, 2012, 16:49

Airsoft School - Quick fix on leaky mags (Lesson 2) - YouTube

ILLusion · January 30th, 2012, 17:39

Quote:

Originally Posted by AKA

Airsoft School - Quick fix on leaky mags (Lesson 2) - YouTube

Good information, but irrelevant for the topic of this thread. He's not having a problem with his mags being unable to hold the gas. They hold the gas just fine.

Slide · January 30th, 2012, 17:39

Quote:

Originally Posted by MultipleParadox

The dripping is actually a feature for you not to get too hot in the summer :P

Hahaha and to share a nice propane odor with your dear friends

FeaR Da Allstar · February 3rd, 2012, 19:44

So I understand this is by design, but is there anyway I can pop a small oring down that hole to fix it? It seems to leak a lot more than if TM was to do this "on purpose"

Styrak · February 3rd, 2012, 21:53

Quote:

Originally Posted by Slide

Ok so i have open up the bottom mag and the O ring on the valvle is very used....so as you say replacing it by a new one will help... Any idea where i can buy this? Thanks!

That o-ring is for sealing the mag at the valve on the inside....not for preventing fill spillage.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

January 30th, 2012, 11:40	#1
Slide Trader rating Join Date: Oct 2010 Location: Montreal	TM Glock 17 magazines - ReFill problem Hi all, i have bhought a TM Glock 17 recently and the gun is working very well but i experienced some trouble with the mags (TM too). There is no leaking when they are filled, but when i fill the mags, it's impossible to make a clean "sealed" refill, gas is going out everywhere. It's like the gas adaptater doesn't fit with the inlet valve. Wich is very classy when you are using propane gas It seems the valve is too little...i have try every angle possible...plastic adaptater, metal adaptater, green gas bottle. Same thing with all of this. So i was wondering if it's a known issue about the Glock 17 TM mags? Or only the two i have bhought...and if you have a solution or recommandation. Thanks guys! Photo of the mag and valve : __________________

January 30th, 2012, 11:57	#3
Spike Privateer Airsoft Trader rating Join Date: Dec 2008 Location: Beaverbank, NS	Most TM mags are like that, very messy fill. Can be solved with an O ring, like Armen said. __________________ I change primaries like other people change socks.

January 30th, 2012, 12:03	#5
Amos Trader rating Join Date: Aug 2006 Location: Japan	TM fill valves are do that. __________________ Custom Builds: FA3674U Krinkov G3SD6

January 30th, 2012, 11:51	#2
Armen000 Trader rating Join Date: Dec 2008	Theres usually a nice little rubber oring that sits in there, from your picture it doesn't look like you have one :P

January 30th, 2012, 11:58	#4
anthon Trader rating Join Date: Jul 2011 Location: Toronto	Yes, TM mags are suposted to make the loud hissing noise when you fill them. AS long as its not leaking after your done filling the mags are normal. I would not recommend using those little rubber o rings, i used one in one of my mags and never again! sure it made them quite when they are filled, but the problem was that it made the mag a hell of a lot harder to fill up.

January 30th, 2012, 12:05	#6
Slide Trader rating Join Date: Oct 2010 Location: Montreal	Ok so i have open up the bottom mag and the O ring on the valvle is very used....so as you say replacing it by a new one will help... Any idea where i can buy this? Thanks! __________________

January 30th, 2012, 12:12	#7
ShelledPants Trader rating Join Date: Feb 2008 Location: Toronto, On	As said above, TM do not fill like KSC, they spray a little when you fill them. This is by design. __________________ Ár skal r?*sa, sá er annars vill fé eða fjör hafa. Sjaldan liggjandi úlfur lær um getur né sofandi maður sigur.

January 30th, 2012, 12:51	#8
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	If it doesn't leak when filled, then that o-ring is fine, even if it appears worn to you. Don't worry about it. As already mentioned, TM fill valves WILL emit gas while filling - again, this is by design and on purpose. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

January 30th, 2012, 13:29	#9
Slide Trader rating Join Date: Oct 2010 Location: Montreal	Perfect! Thanks guys! __________________

January 30th, 2012, 16:49	#11
AKA Trader rating Join Date: Dec 2011 Location: st.john's NL	Airsoft School - Quick fix on leaky mags (Lesson 2) - YouTube __________________

February 3rd, 2012, 19:44	#14
FeaR Da Allstar Trader rating Join Date: Jan 2012 Location: Newfieland	So I understand this is by design, but is there anyway I can pop a small oring down that hole to fix it? It seems to leak a lot more than if TM was to do this "on purpose"

TM Glock 17 magazines - ReFill problem

Doctor's Corner