VSR-10 stock problem

Joshery · December 1st, 2012, 17:42

(Edit: the problem isn't in the stock)
Hi guys, sorry if I sound like an idiot, but I can't get my VSR-10 barrel/bolt/trigger assembly back into my stock! I'm completely stumped because I've done this about 60 thousand times and helped people do it when they have problems.
I'll post some pictures, but basically: The rear end of the barrel, where the bolt is, fits in fine as usual, but the metal box on the barrel underneath the hop-up is 2-3 cm too far forward so it's keeping me from pushing the barrel down into the gun.
Any input would be greatly appreciated.

XZIVR · December 1st, 2012, 18:22

Might be a stupid question but is the barrel screwed in tight to the receiver? That's all I can think of that would cause it to sit THAT far forward..

Joshery · December 1st, 2012, 19:43

It doesn't seem like it'll go on any tighter, but I can give it a try... I don't want to over tighten it though.

XZIVR · December 1st, 2012, 19:45

No, once it shoulders out it's tight. Plus you have to back it off to fit that screw in the bottom anyway.

Are you sure the barrel mounting block is on properly as well?

Joshery · December 1st, 2012, 19:55

Yea, it's on right.

R.I.T.Z · December 1st, 2012, 20:14

got any photos?

Joshery · December 2nd, 2012, 17:52

I unscrewed the outer barrel and wiped off the grease and was able to put it on tighter. Problem solved.

XZIVR · December 2nd, 2012, 17:57

uhh, look at a ruler dude, no way that would make it sit forward 2-3cm.. maybe you meant mm?

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

December 1st, 2012, 17:42	#1
Joshery Trader rating Join Date: Dec 2011 Location: Outlook, Saskatchewan	VSR-10 stock problem (Edit: the problem isn't in the stock) Hi guys, sorry if I sound like an idiot, but I can't get my VSR-10 barrel/bolt/trigger assembly back into my stock! I'm completely stumped because I've done this about 60 thousand times and helped people do it when they have problems. I'll post some pictures, but basically: The rear end of the barrel, where the bolt is, fits in fine as usual, but the metal box on the barrel underneath the hop-up is 2-3 cm too far forward so it's keeping me from pushing the barrel down into the gun. Any input would be greatly appreciated.

December 1st, 2012, 18:22	#2
XZIVR Trader rating Join Date: Mar 2011 Location: Calgary, AB	Might be a stupid question but is the barrel screwed in tight to the receiver? That's all I can think of that would cause it to sit THAT far forward..

December 1st, 2012, 19:43	#3
Joshery Trader rating Join Date: Dec 2011 Location: Outlook, Saskatchewan	It doesn't seem like it'll go on any tighter, but I can give it a try... I don't want to over tighten it though.

December 1st, 2012, 19:45	#4
XZIVR Trader rating Join Date: Mar 2011 Location: Calgary, AB	No, once it shoulders out it's tight. Plus you have to back it off to fit that screw in the bottom anyway. Are you sure the barrel mounting block is on properly as well?

December 1st, 2012, 19:55	#5
Joshery Trader rating Join Date: Dec 2011 Location: Outlook, Saskatchewan	Yea, it's on right.

December 1st, 2012, 20:14	#6
R.I.T.Z Crackers Trader rating Join Date: Mar 2009 Location: The Shwa	got any photos?

December 2nd, 2012, 17:52	#7
Joshery Trader rating Join Date: Dec 2011 Location: Outlook, Saskatchewan	I unscrewed the outer barrel and wiped off the grease and was able to put it on tighter. Problem solved.

December 2nd, 2012, 17:57	#8
XZIVR Trader rating Join Date: Mar 2011 Location: Calgary, AB	uhh, look at a ruler dude, no way that would make it sit forward 2-3cm.. maybe you meant mm?

VSR-10 stock problem

Newbie Tank