KSC/KWA USP slide disassembly

koztah · February 19th, 2009, 00:58

I have this KWA USP and I'm trying to swap the slide for one with trades.

The problem is, I can't seem to get the damn blowback assembly out.

I removed the screw with an allen key, removed the rear sight and the whole assembly sort of wobbles but won't come out.

If you look at this diagram:

http://s78.photobucket.com/albums/j1...s/ee7e6801.jpg

I think part #3 is keeping it in there, but I can't for the life of me figure out how to get it off.

Also, trying to get the inner barrel out of the outer barrel, there's this small pin I think is holding it in, and I'm unsure how to get that pin out also.

Any input would help.

dirtdiver · February 19th, 2009, 01:28

one arm of the blowback unit has a small indentation in it, use a small flathead to pull that arm slightly towards the center of the slide then turn the slide upside down and hit it against your hand the unit should fall out. For the barrel turn the screw underneath and pop the small plate up make sure not to lose the spring and pin! Hope this helps I'm at work and don't have part numbers.
Cheers
Dirtdiver

koztah · February 19th, 2009, 02:06

Ha! Yes, that did it.

However, my new slide didn't have an extractor with, so I tried to pry the one off my old slide and discovered...it's very cheap plastic.

Any idea where I can buy another of those little plastic bits? It's part 3 which I mentioned above.

Also, any ideas as to how to keep the front sight on? Friction isn't going to do it for very long, I'd hate to lose a sight on the field. Metal glue?

dpvu · February 19th, 2009, 02:11

Superglue will hold that front sight on. Just make sure it's lined up where you want it and don't overdo it.

Amos · February 19th, 2009, 04:42

I put a dab of blue loc-tite under my front sight, then lined it up and let it dry.

koztah · February 19th, 2009, 16:53

Thanks for your replies!

Incidentally, I e-mailed KWA to see about getting a new extractor since it wasn't listed on their website.

They do sell it, it just isn't available for online order. You have to call in to get it. So if any of you guys ever wreck your extractor while trying to get it out:

"We do have the part available for purchase and below is the part information for your consideration.

PT0003-0003 Extractor $3.78
Shipping not included - $7.35 (USPS-Priority Mail)

Please call us to place your order since the part is not listed on our website and by doing so we can expedite your order quickly. Mention ticket #1195 when placing the order."

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

February 19th, 2009, 02:11	#4
dpvu Trader rating Join Date: Mar 2008 Location: Calgary	Superglue will hold that front sight on. Just make sure it's lined up where you want it and don't overdo it. __________________ JG HK416 KWA USP

February 19th, 2009, 04:42	#5
Amos Trader rating Join Date: Aug 2006 Location: Japan	I put a dab of blue loc-tite under my front sight, then lined it up and let it dry. __________________ Custom Builds: FA3674U Krinkov G3SD6

February 19th, 2009, 00:58	#1
koztah Trader rating Join Date: Apr 2007 Location: Montreal, Qc	KSC/KWA USP slide disassembly I have this KWA USP and I'm trying to swap the slide for one with trades. The problem is, I can't seem to get the damn blowback assembly out. I removed the screw with an allen key, removed the rear sight and the whole assembly sort of wobbles but won't come out. If you look at this diagram: http://s78.photobucket.com/albums/j1...s/ee7e6801.jpg I think part #3 is keeping it in there, but I can't for the life of me figure out how to get it off. Also, trying to get the inner barrel out of the outer barrel, there's this small pin I think is holding it in, and I'm unsure how to get that pin out also. Any input would help.

February 19th, 2009, 01:28	#2
dirtdiver Trader rating Join Date: Nov 2008 Location: Ontario	one arm of the blowback unit has a small indentation in it, use a small flathead to pull that arm slightly towards the center of the slide then turn the slide upside down and hit it against your hand the unit should fall out. For the barrel turn the screw underneath and pop the small plate up make sure not to lose the spring and pin! Hope this helps I'm at work and don't have part numbers. Cheers Dirtdiver

February 19th, 2009, 02:06	#3
koztah Trader rating Join Date: Apr 2007 Location: Montreal, Qc	Ha! Yes, that did it. However, my new slide didn't have an extractor with, so I tried to pry the one off my old slide and discovered...it's very cheap plastic. Any idea where I can buy another of those little plastic bits? It's part 3 which I mentioned above. Also, any ideas as to how to keep the front sight on? Friction isn't going to do it for very long, I'd hate to lose a sight on the field. Metal glue?

February 19th, 2009, 16:53	#6
koztah Trader rating Join Date: Apr 2007 Location: Montreal, Qc	Thanks for your replies! Incidentally, I e-mailed KWA to see about getting a new extractor since it wasn't listed on their website. They do sell it, it just isn't available for online order. You have to call in to get it. So if any of you guys ever wreck your extractor while trying to get it out: "We do have the part available for purchase and below is the part information for your consideration. PT0003-0003 Extractor $3.78 Shipping not included - $7.35 (USPS-Priority Mail) Please call us to place your order since the part is not listed on our website and by doing so we can expedite your order quickly. Mention ticket #1195 when placing the order."

KSC/KWA USP slide disassembly

Upgrades & Modifications